Sweat-baked headset bolt

Post your questions about bike maintenance, bike problems, kit issues, goggle issues – anything to do with the kit you have which isn’t quite going to plan and you’re looking for an answer why.

Sweat-baked headset bolt

Postby kfjatek » 13 May 2016 14:24

I have a bit of play in the headset on Nighthawk. After enough miles Argon 18's revolutionary "3D head tube" must have gone a bit loose and needs tightening up.

The challenge is, my headset bolt has corroded with sweat etc. and the 5mm hex key that would normally work to disassemble the headset and inspect it just slides in the slot.

Any tried and tested ways to remove it? (I guess I'll need to swap it out for a new one anyway)

:ugeek:
2015:
26/04 Southampton 10k
30/05 Sieraków Triathlon
21/06 Dambuster Triathlon
29/08 Club Relays
27/09 Hever Triathlon
User avatar
kfjatek
SGM
 
Posts: 3219
Joined: 26 Sep 2012 12:16
Location: London/Surrey

Re: Sweat-baked headset bolt

Postby ris » 13 May 2016 15:07

Mr mofo to this thread about stripped threads to bring his wisdom and correct saw angle, please. :lol:

i'd suggest drilling it out, but don't do that. get a shop to do it. or bop.
most disturbing in lycra, 2010, 2012, 2013
club champ 2015
User avatar
ris
 
Posts: 4444
Joined: 05 Jan 2010 15:15
Location: wilts
Blog: View Blog (26)

Re: Sweat-baked headset bolt

Postby Kevy427 » 13 May 2016 16:50

Squirt GT85, WD40 or a similar penetrating lubricant (fnarr, fnarr) around the area and leave to soak for a few hours then try again. You could always try Röstshock (Reca/Würth) or similar product to lower the temperature and break the bond. Failing that, drill it out using a left-hand drill bit and extractor. Another thing to try is using a Torx in there as these can bite in a little bit more. Gently tap it in with a hammer to get a bit more purchase

Invest in a decent set of 3/8" drive hex/Allen sockets as the T-handles won't give you enough torque to undo something like that, and the cheaper stuff is a bit Chad Valley and made of cheese. I'm an ex Snap-On dealer so know one or two things about tools
Pedalling between cake shops
User avatar
Kevy427
 
Posts: 4223
Joined: 06 Nov 2010 18:39
Location: The Principality of Pagham

Re: Sweat-baked headset bolt

Postby Jack Hughes » 13 May 2016 20:31

"Sweat-baked headset bolt"

Sounds nice. But what's for pudding?
Omnia Vanitas

Officially Bad For Age
User avatar
Jack Hughes
 
Posts: 11003
Joined: 05 Jan 2010 17:19
Location: God's own county

Re: Sweat-baked headset bolt

Postby Seasider71 » 16 May 2016 10:41

if it is the bolt head that has rounded, put a thin elastic band over the top of the hex key before inserting it - this helps to grip the rounded edges.

If it is something else, buy a new bike :D
Striving for glory.....and failing magnificently.
2017
MAY - Enduroman Double
User avatar
Seasider71
 
Posts: 2084
Joined: 10 Jan 2010 20:22
Location: Dinnington, Sheffield
Blog: View Blog (1)


Return to Technical FAQ

Who is online

Users browsing this forum: No registered users and 1 guest

cron